View T1530D-S_4536302.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ACTIVE SIGNAL AMPLIFIER Iin & Vout
T15/16/25/26_D/S
DESCRIPTION
The series is a high integration, high efficiency polygonal - line active isolation amplifier module, with anterior circuit current signal input and posterior current signal output. These modules are embed with a high efficiency isolated micro-power source, which can provide a electrics-feed for signal input. In the two-wire three-wire and four-wire circuit applications, our products largely predigest customers' design helpfully improve the using room ratio of PCB. Adopting electromagnetism isolation technology, it is available to keep high accuracy and natural extremely low temperature drift. The isolation voltage among the input, output, power supply and isolated power output can up to 2.5KVDC.
PRODUCT PROGRAM
Part Number T1530D/S T1533D/S T1630D/S T1650D/S Power Supply 24V 24V 24V 12V Input 4-20mA 4-20mA 4-20mA 4-20mA Output 0-10V 0-10V 0-5V 0-5V Isolation Channels Power Output NONE 24V NONE NONE 1 1 1 1
Note: We could also offer customer design for special input and output.
ELECTRICAL CHARACTERISTICS
Power Supply Power Supply Data Power Dissipation Power Protection Isolation Power Output Data Output Voltage Output Current Input Signal Input Impedance Overload Output Data Output Signal Load Power Supply 5% 2W Reverse protection (Nominal) 10% 25mA See above Voltage Drop250mV(At input=20mA) 300mA See above 1KAt output=max
FEATURES
Four-port isolationAmong input, output, power supply and Isolation Power output High accuracy (0.1% F.S.) High linearity (0.1% F.S.) Isolation voltage(2500VDC/60S) High frequency response(15KHz) Extremely low temperature(35PPM/) Industry standard(Operating Temperature Range:-25C to 71C) High reliability(MTBF500,000 hours)
Input Data
TRANSMISSION CHARACTERISTICS
Offset Gain Error Temperature Drift 0.1%F.S. 0.1%F.S. 0.0035%F.S./ (-25 to +71 )
ISOLATION CHARACTERISTICS MODEL SELECTION
Galvanic Isolation Isolation Voltage Insulation Resistance
Pa ckage style Iso lation po w er o utpu t Pow e r supp ly Out put Inp ut Isolatio n Amp lifier
Four-port isolationAmong input, output, power supply and Isolation Power output 2.5KVDC (Tested for 1minute and 1mA max, humidity < 70%) 1000M,500VDC (Among signal input ,signal output ,power supply and isolation power output)
TXXXXD
OTHER CHARACTERISTICS
Ambient temperature Package Weight Operation temperature:-25 to +71 Transport and Storage temperature:-50 to +105 DIP24/SOIC24 About 10g No dusts, gases of fiercely vibration, impulsion or gases that may erode to the components surrounded
MORNSUN Science & Technology co.,Ltd.
Address: 2th floor 6th building, Huangzhou Industrial District, Guangzhou, China Tel: 86-20-38601850 Fax:86-20-38601272 Http://www.mornsun-power.com
The Environment in use
Note: 1. All specifications measured at TA=25C, humidity<75%, nominal input voltage and rated output load unless otherwise specified. 2. Only typical models listed, specifications of custom product may be different. Please contact our service people directly for certain conditions.
The copyright and authority for the interpretation of the products are reserved by Mornsun
Specifications subject to change without notice. T15/16/25/26_D/S A/2-2008 Page 1 of 2
SCHEMATIC DIAGRAM
24Power supply 23+ 13Isolation Power Output 14+ Iin12Signal input 11+ Ii n+ Vout+ 3+ Signal output Vout1-
APPLICATION NOTE
1. Please read instruction book carefully before using the product. If you have any question, please contact with our technical support. 2. Please don't install in the dangerous zone. 3. The power supply is direct voltage. 220V alternating current is forbidden.. 4. Don't divide the product privately in case the equipments ineffective or go wrong.
AFTER SERVICE
APPLICATION CIRCUIT DIAGRAM
1. Products are carefully inspected and controlled before going out from our factory. If they operated abnormally or there were something wrong in the inner parts, please contact with our agents near you or technical support in our company as soon as possible.
Power Supply
Isolation Power Output
24 23 22 21 20
PinPin+ NC NC NC
16 15 14 13
NC NC PoutPout+
2. 3 years warranty since the delivery date. During the period of quality guaranteeour company will repair or change free of charge if product has any quality problem in the process of normally using.
Input
SoutNC Sout+ NC NC
12345
NC NC Sin + Sin -
TxxxxD
9 10 11 12
Output
APPLICATION CIRCUITS
See A GUIDE TO INSTRUMENTATION ISOLATION AMPLIFIERS for more detail.
PACKAGING SIZE AND TERMINAL DESCRIPTION
First Angle Projection
SOIC Package 10.20 (0.397) 10.20 (0.397) DIP Package
4.00 (0.157)
0.70(0.028)
27.94 (1.100) 32.30(1.272)
32.30(1.272) 18.60(0.732)
14.40 (0.560)
0.30 (0.012)
1.150.15 (0.0 450.006)
16 15 14 13
24 23 22 21 20
14.40 (0.560)
RECOMMENDED FOOTPRINT Top view,grid:2.54mm(0.1inch) diameter:1.00mm(0.039inch)
24 23 22 21 20
16 15 14 13
19.24 (0.757)
2.00 0.079
Vin-
Vin-
12345 12345 9 1011 12
9 1011 12
1.00 0.039 Pin C onnection PIN FUNCTION OutputOutput+ Input+ 24(Vin-) Others Isolation Power OutputNC:No Connection Note: Unit:mm(inch) Pin section:0.50*0.30mm(0.020*0.012inch) Pin tolerances: 0.10mm( 0.004inch) General tolerances :0.25mm( 0.010inch) PIN FUNCTION Isolation Power Output+ Power Sup ply+ Power SupplyNC
The copyright and authority for the interpretation of the products are reserved by Mornsun
Specifications subject to change without notice. T15/16/25/26_D/S A/2-2008 Page 2 of 2
0.65 (0.026)

▲Up To Search▲

Price & Availability of T1530D-S

	To Download T1530D-S Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .